Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
The article author is making several good points related to Tools You Need to Install a New Bathtub overall in this post just below.
Installing a bath tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open up a wall to remove the old tub and also place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. See to it you have actually certified on your own for the work and also fit attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is better to consider using one prior to you start. Chances are you might require an expert plumber to make tube links.
This post will certainly assist you mount a new bathtub in your shower room if you have actually currently purchased a brand-new bathtub and do not require to transform the setup of your previous supply of water pipelines.
Your tools and also material checklist ought to make up the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before going on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the tub in the called for placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the tub up until the level reads level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Load the tub and also examine the overflow outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait till the tub has actually been used a minimum of when as this will settle it into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines remain in place between the faucet and the sink. Secure the tap in place with the producer supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind must be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can break rather early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that piece of writing about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Are you aware of another person who is truly interested in How to Install a Bathtub? Do not hesitate to promote it. We appreciate reading our article about How to Install a Bathtub Yourself.
We're on standby! Report this page